Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
The article author is making a number of good pointers relating to How to Install a Bathtub Yourself as a whole in this article beneath.
Mounting a bath tub isn't specifically rocket science, however it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently obtainable, the job can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will need an assistant to vacate the old tub and also set in the new one. Make certain you have actually certified on your own for the work and fit attempting it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will assist you install a new bath tub in your bathroom if you have actually currently gotten a new tub as well as don't need to transform the arrangement of your previous water pipes.
Your devices and also product checklist must comprise the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the faucets to drain pipes any water staying in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the limited accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making sure that the washing machines remain in place in between the tap and also the sink. Safeguard the tap in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous kind must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four small factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the tub up until the level checks out level.
To set up taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water and check all joints and new pipework for leakages and tighten them if required. Fill the bath tub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub needs to wait up until the tub has been utilized at least when as this will resolve it right into its last position.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as installations. They are marketed in tubes and cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can crack relatively early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very taken with Installing A Bathtub and I hope you enjoyed reading our blog entry. For those who enjoyed reading our blog entry kindly remember to pass it around. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule A Free Estimate Report this page